Honda Fit manuals

Honda Fit: Removal (Part -3)

Second generation (2007-2026) / Honda Fit 2007-2026 Repair Manual / Chassis / Steering / Steering Gear Assembly / Steering Gearbox Removal and Installation / Removal (Part -3)

  1. Remove the secondary HO2S harness bracket (A) from the steering gearbox.

    NOTE: Do not disconnect the secondary HO2S 4P connector and the secondary HO2S.

    2. @font-face{font-family: "Honda_SymbolMarkeng";src:url(/statics/ho_prod_2/txt/Honda_SymbolMark_enu3.txt);}@font-face{font-family: "Honda_Special_Symbols";src:url(/statics/ho_prod_2/txt/Honda_Special_Symbols2.txt);} 6 x 1.0 mmA

  2. Remove the splash shield.

  1. Remove the lower torque rod (A).

    2. @font-face{font-family: "Honda_SymbolMarkeng";src:url(/statics/ho_prod_2/txt/Honda_SymbolMark_enu3.txt);}@font-face{font-family: "Honda_Special_Symbols";src:url(/statics/ho_prod_2/txt/Honda_Special_Symbols2.txt);} AM/T14 x 1.5 mmReplace.A/T12 x 1.25 mmReplace.14 x 1.5 mmReplace.14 x 1.5 mmReplace.

  1. Attach a transmission jack (A) to the middle of the front subframe (B), and support the front subframe securely by raising the transmission jack.

    2. @font-face{font-family: "Honda_SymbolMarkeng";src:url(/statics/ho_prod_2/txt/Honda_SymbolMark_enu3.txt);}@font-face{font-family: "Honda_Special_Symbols";src:url(/statics/ho_prod_2/txt/Honda_Special_Symbols2.txt);} C14 x 1.5 mmReplace.AC14 x 1.5 mmReplace.B

  2. Remove the front subframe mounting bolts (C).

  3. Lower the front subframe and steering gearbox as an assembly by lowering the jack slowly.

  1. Remove the steering gearbox (A) from the front subframe (B).

    2. @font-face{font-family: "Honda_SymbolMarkeng";src:url(/statics/ho_prod_2/txt/Honda_SymbolMark_enu3.txt);}@font-face{font-family: "Honda_Special_Symbols";src:url(/statics/ho_prod_2/txt/Honda_Special_Symbols2.txt);} 10 x 1.25 mmReplace.AB10 x 1.25 mmReplace.10 x 1.25 mmReplace.10 x 1.25 mmReplace.10 x 1.25 mmReplace.

  1. Remove the pinion shaft grommet (A).

    2. @font-face{font-family: "Honda_SymbolMarkeng";src:url(/statics/ho_prod_2/txt/Honda_SymbolMark_enu3.txt);}@font-face{font-family: "Honda_Special_Symbols";src:url(/statics/ho_prod_2/txt/Honda_Special_Symbols2.txt);} A

 

See also:

A/T Housing Idler Gear Shaft Removal and Installation (A/T)
Remove the snap ring (A), the cotter retainer (B), and the cotters (C) from the idler gear shaft (D), then remove the idler gear shaft. Do not distort the snap ring. Check ...

Audio System
You can play music from a wide array of media sources. You can also control the audio system using voice commands. ...

Steering Angle Sensor Replacement
SRS components are located in this area. Review the SRS component locations   and the precautions and procedures. NOTE: Do not damage or drop the combination switch as the steering angle ...

Categories

© 2026 Copyright www.hfitinfo.com