Honda Fit manuals

Honda Fit: Rear Seat Belt Replacement

Rear Seat Belt

NOTE: Check the rear seat belts for damage, and replace them if necessary.

  1. Remove these items:

    • Rear door inner seal, as needed

    • Tailgate weatherstrip, as needed

    • Cargo floor

    • Cargo floor box, with temporary repair kit (TRK)

    • Rear trim panel

    • Cargo area side trim panel

  1. Pull the carpet back as necessary, and remove the lower anchor bolt (A).

  2. A7/16-20 UNF32 Nح (3.3 kgfح, 24 lbfئt)
  1. Remove the upper anchor cap (A), and remove the upper anchor bolt (B).

  2. AB7/16-20 UNF32 Nح (3.3 kgfح, 24 lbfئt)
  1. Remove the upper retractor mounting bolt (A) and the lower retractor bolt (B), then remove the rear seat belt (C) and the retractor (D).

  2. CDA6 x 1.0 mm9.8 Nح (1.0 kgfح, 7.2 lbfئt)B7/16-20 UNF32 Nح (3.3 kgfح, 24 lbfئt)
  1. Install the seat belt and the retractor in the reverse order of removal, and note these items:

    • Tighten the bolts by hand first, then tighten to the specified torque.

    • Check that the retractor locking mechanism functions.

    • Assemble the washers and the collar on the upper anchor bolt as shown.

    • Before installing the anchor bolts, make sure there are no twists or kinks in the seat belt.

  2. Upper anchor bolt installation

    SPRINGWASHERCOLLARUPPER ANCHORTOOTHEDLOCK WASHERUPPER ANCHORBOLT

Rear Center Shoulder Seat Belt

  1. Remove the headliner.

  1. Remove the front retractor mounting bolt (A) and the rear retractor bolt (B), then remove the center seat belt and the retractor (C).

  2. A6 x 1.0 mm9.8 Nح (1.0 kgfح, 7.2 lbfئt)B7/16-20 UNF32 Nح (3.3 kgfح, 24 lbfئt)C
  3. Install the center seat belt and the retractor in the reverse order of removal, and note these items:

    • Tighten the bolts by hand first, then tighten to the specified torque.

    • Check that the retractor locking mechanism functions.


Rear Seat Belt Buckles and Center Shoulder Seat Belt Detachable Anchor

  1. Lift both rear seat cushions up.

  1. Pull the rear seat belt buckles (A) and the rear center seat belt detachable anchor (B) out through the elastic straps (C) on the seat cushions.

  2. ABC
  3. Place the seat belt buckles and seat belt detachable anchor on the floor underneath the seat cushions.

  4. Fold both rear seat-backs.

  1. Lift up the cargo floor lids (A), and remove the anchor bolts (B).

  2. AB7/16-20 UNF32 Nح(3.3 kgfح, 24 lbfئt)
  3. Lift both rear seat cushions up.

  1. Remove the seat belt buckles (A) and the center seat belt detachable anchor (B).

  2. AB
  1. Install the buckles and the anchor in the reverse order of removal, and note these items:

    • Tighten the bolts by hand first, then tighten to the specified torque.

    • Assemble the washers on the anchor bolts as shown.

Left side anchor bolt installation

SPRING WASHERANCHOR PLATEANCHOR BOLTTOOTHEDLOCK WASHER

Right side anchor bolt installation

WASHERANCHOR PLATEANCHOR BOLTTOOTHEDLOCK WASHER
See also:

Reassembly
Apply Molykote 44MA grease to the sliding surface of the pivot pin (A) and the parking brake lever (B) for the rearward brake shoe (C). @font-face{font-fami ...

Tire Service Life
The life of your tires is dependent on many factors, including driving habits, road conditions, vehicle loading, inflation pressure, maintenance history, speed, and environmental conditions (even ...

What to Do If
The ignition switch does not turn from to . Why? ● The steering wheel may be locked. ● Try to turn the steering wheel left and right while turning the ignition key. The i ...

© 2025 Copyright www.hfitinfo.com